Products | Customer Support | Houses | DownloadsHome PageClearSite MapClearMailClearPrintClearRssClearΧώρες Ευρωπαϊκής Ένωσης
Navigation
Products
Punching
Shearing
Laser
Combi Machines
Plasma
Bending
Software
Welding
Laser Welding
Resistance Welding
Robot Welding Systems
Clinching
Robotic Systems
Routers
Lines
Presses
Fasteners
Deburing
Air Ducting
Band Saw
Notching
Other
Search

 
Log In
Username

Password

Home : Products : Welding : Resistance Welding : Controls : TE185 - Constant current microprocessor control unit

TE185 - Constant current microprocessor control unit

 
WELDING CONTROL UNIT TE 185

TE 185 is a microprocessor welding control unit for single-phase resistance welders. The welding control unit is used to control the welder parts and, in particular, the thyristor regulating the welding current. TE 185 control unit can be programmed for working under two different operating modes: standard one and constant current. It is possible to program and to store up 15 different welding programs. All the programs can be recalled directly from the keyboard and from an external source by means of a PLC. Each program can assume all the configurations included between the simplest 4 times cycle, up to the most complex one, which can include the slopes, the pulses, the postheating, the forging and the minimum and maximum current limits.

TE185 - Constant current microprocessor control unit

MAIN FEATURES

  • 15 welding programs selectable by keyboard and by an external device.
  • 16 programmable parameters.
  • Control of 3 solenoid valves 24 Vdc 7,2 W Max with protected output against short circuit.
  • Double operating mode: standard and constant current.
  • Measure and display of the welding current in kA.
  • Measure and display of the max. welding current conduction angle.
  • Adjustment of the welding time in half-periods.
  • Welding current limits for each program under standard operating mode.
  • Current conduction angle limits under constant current operating mode.
  • Counter of the performed welds.
  • Output of endcycle with relay, also selectable as interlock.
  • Output signal for out-of-limits spots with relay.
  • Automatic compensation against voltage drops under standard operating mode.
  • Minimum current compensation function under standard operating mode.
  • Restart key and outputs enabling under Watch-dog control.
  • Serial communication by means of insulated RS-232 interface (optional).
  • Removable key for programming or for run.
  • Integrated ammeter with four different capacities to select (18,36,45,90 kA).
  • Key to select foot control or two hands control.
  • Possibility to eliminate the autoretain of the start signal during the welding process.
  • Self-adjustment to the network frequency 50/60 Hz.

PROGRAMMABLE PARAMETERS

PARAMETER RANGE
1° SQUEEZE 01 - 99 cycles
SQUEEZE 00 - 99 cycles
FORGE DELAY 00 - 99 cycles
SLOPE UP 00 - 29 cycles
WELD TIME 1 00.5 - 99.5 cycles
CURRENT 1 01 - 99 % 2.0 - 90.0 kA *
COLD TIME 1 00 - 50 cycles
IMPULSE N. 01 - 09
SLOPE DOWN 00 - 29 cycles
COLD TIME 2 00 - 50 cycles
WELD TIME 2 00.0 - 99.5 cycles
CURRENT 2 00 - 99 % 2.0 - 90.0 kA *
HOLD TIME 01 - 99 cycles
OFF TIME 00 - 98 cycles
MIN. CURR. 0 - 90 kA 0 - 180° *
MAX. CURR. 0 - 90 kA 0 - 180° *

* under constant current operating mode

 

Specifications subject to change without notice.


Bookmark and Share


 Υποκατηγορίες:
Stationary
Guns
• Controls  
[ TE25 - Basic microprocessor control unit | TE90 - Microprocessor control unit | TE91 - Microprocessor control unit | TE93 - Microprocessor control unit | TE95 - Microprocessor control unit for cable guns | TE180 - Advanced microprocessor control unit | TE183 - Three-phase microprocessor control unit | TE185 - Constant current microprocessor control unit | TE195 - Advanced microprocessor control unit for suspended guns | TE300 - Microprocessor control unit for suspended guns | TE450 - Constant current microprocessor control unit for suspended guns ]
Accessories
Car Body Repair
Special Machines
Slide Show
Decor Image
Online Visitors
Online Επισκέπτες
2
Total Visitors
Μοναδικοί Επισκέπτες
69321
Total Visits
Επισκεψιμότητα
1034600

© 2024 - EUROMACH S.A.

32 kithirion Ave., 174 56 Alimos, Athens - GREECE. Tel: +30210-9967798-9967855 Fax: +30210-9955930

Home | Site Map | Print | Rss | Contact | Disclaimer | Protocol Online Marketing